Search results

  1. G

    SSQA Linear Actuator

    I decided to build this. It is a little slow. Usually I can activate it while I am driving so no waiting. https://www.amazon.com/dp/B0DMSKMLF5?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1 https://www.amazon.com/dp/B0C7QN96DS?ref=fed_asin_title&th=1...
  2. G

    Split-fire Log Splitters split both ways.

    I have the 2265. It has plenty of power. You split on both the forward and return stroke. Pretty fast. https://split-fire.com/us/log-splitter-2265-us/
  3. G

    Grease Behind Starter L4060HSTC

    I took off the starter and there is a bunch of grease back there. I don’t think that is normal.
  4. G

    1,500 hour Maintenance

    EGR Cooler I have seen other brands that the heat exchanger is plugged with soot. Has anyone checked it? Has anyone checked the intake system for soot from the EGR?
  5. G

    Heater Blower Replacement

    If anyone needs a blower motor Kubota gets$1,000.00 You can get it for $40.00 at AutoZone. I don't need one. I just saw this video. https://www.autozone.com/cooling-heating-and-climate-control/a-c-heater-blower-motor/p/four-seasons-hvac-blower-motor-35516/914365_0_0
  6. G

    EGR Soot in the air intake

    6.7 Powerstroke EGR Maintenance Do the Kubota's have the same issue?
  7. G

    T/M Controller (IG)

    I have a L4060HSTC It blew the T/M Controller fuse. A new fuse has not blown. I would just like to know what the T/M Controller is.
  8. G

    Low oil pressure buzzer

    I have a ZD1211 and a L4060HSTC. Both of them I installed a relay that runs the horn. I ran a wire to the oil pressure switch. I disconnected the wire from the switch that went to the light. When you don't have oil pressure the switch goes to ground. I used the same horn that ZD1211 uses if...
  9. G

    I have a Sabre Samurai Cutter for sale

    For some reason my Kubuta L4060 does not have the flow rate that this needs. I have about $3,000.00 in it with the hoses and the mount I made. It has not been used much. $1,500.00 and it is yours. Only requires 3 to 4.5 gal/min. https://www.cutthat.com/product/sabre-samurai-cutter-2/ I am...
  10. G

    L4060HSTC PTO Pressure

    I want to test the pressure because sometimes the PTO takes about a minute to shut off. I always start and stop the PTO at idle speed. The test port threads are PT 1/8. I am having trouble finding a test kit with that size fitting. I have a gauge that is 0-600 PSI with 1/4 NPT.
  11. G

    L4060 HSTC PTO takes a minute to disengage sometimes.

    I have a 12' woods finish mower. I always engage and disengage the PTO at idle. If the mower keeps spinning and I put it is some tall grass it stops. If I wait a minute it stops. If I rev it and back to idle it stops. It is not electrical because I can get of the seat and the tractor keeps...
  12. G

    L4060HSTC Seat with good lumber support.

    The arm rests on the stock seat is 23" wide. You can go wider than that. The stock seat has 4" of travel. I called 3 Kubota dealers asking about the air ride Kubota seat. One dealer said the stock seat is great and they never sold the air ride seat. 2 dealers said they have sold them but...
  13. G

    algae in fuel

    My water separator was getting algae in it. I am using PS Bio Kleen. The big pieces on the paper towel is grease. The small stuff is algae. I have 6 5 gal. gas cans. They have maybe a pint of fuel left in them. I emptied them into the coffee filter and found grease and algae in the cans. The...
  14. G

    L4060HSTC fuel tanks.

    I think I had around 6 gal. in the tanks. I got about 1 gallon out of the RH tank. Their is a check valve in the 2"+- line that goes between the tanks. I had the RH tank on the floor. Over night it put about 4 gallons in the RH tank that I sucked out. Should the RH and LH tank have about the...
  15. G

    HST4060HSTC

    Error No. 90 HST-F Solenoid NG. I ran over 1 stick. It made it between the brake rod and the main oil line. Ripped the wires out of the servo regulator. I think from Kubota you have to buy the whole harness. I don't if their is a +- on these. I would like to buy the plugs with 6" of wire...
  16. G

    Front wheel bearing fail L3540

    I broke the outside bearing twice. The first time at 1350 hours hauling heavy clay. The second time at 1900 hours moving snow with the bucket. The second time was a light load. I don't understand the second time. I am using 80W 90 oil. It was full.
  17. G

    The BEST Way TO Perform a Parasitic Draw Test

    I see a lot of people that have issues with electric troubleshooting.
  18. G

    Bacteria in fuel

    I bought a 2017 4060HSTC with 107 hours on it on 06/19/21. On 07/09/2021 I noticed some junk in the water separator an started treating it with PS Bio Kleen. On 10/10/2021 today I to the water separator apart and I am getting a little junk inside the screen. The tractor has 250 hours on it now...