Search results

I'm dealing with some medical issues right now. I'll continue tomorrow.

Still got it? Can you ship it? I'd need some measurements to see it if will work with my 4 in 1 bucket.

Bought it used. Speed/direction pedal did not always return to neutral, Found the "damper" had been removed and "fixed" with a Rube Goldberg setup of springs. DID work OK(ish) but often had to nudge the pedal into neutral. Bought a new "damper", removed the springs and, as I recall, was...

No, never resolved. Still seems to happen occasionally. I'll look into it again this spring.

That looks like it. Thanks. Pricey little thing.

Was looking for a replacement label for B21/TL421, specifically the "directions" lable (with arrows) for the FEL control valve. This one is illegible. While I pretty much know how to operate it, it bothers me and upon occasion I might ask someone to operate the FEL for one reason or another...

Some one might know. I have an old Ebay special "Colossal Tech CUT-50D" with the original "touch start" torch. Wanted to convert it to a "pilot arc" as I may be doing a lot of cutting on rusted and painted steel. The cutter does not have a "pilot" connector, but it does have a built in ground...

Must be early. Or something. But not quite following the measurements advice. The "distance" being the length of extension? Say from eye to eye on each of the cylinder? Then after mounting the adapter plate check and reset if needed? I still have to "eyeball" or otherwise determine what...

Yeah. I'm thinking to re-install the ATI on the FEL and mount the adapter plate and line the tractor and the bucket up pretty much as in the pictures, then slice off those ears at that angle as close and high on the bucket as I can get. Gotta sharpen up my plasma cutting technique too. I...

Because they made good stuff? Because now you "pay when it ships"? According to what I have read any way. I have one EA rake bought several years ago and am pleased with it. But I would think long and hard before buying anything else from them. And only if "pay when shipping" is a reality.

I have a B21 for which I purchased an ATI SSQA adapter. Pricey, but very well built, to my amateur eyes. Put it on and tested it with a SSQA attachment I had and loved it. But when it came time to being cutting and welding the WRlong bucket, which has a curved back, for whatever that's...

I know this is a years old thread, but, was thinking of a QA adapter. Have a Bxpanded ripper tooth and am happy with it. However, I have nothing but "rocky soil" and "tree stumps". An email to them via their web site received no response to my question about the situation. Makes no sense for...

Did you ever get around tuit?

So, getting back to this, the 3pt dropping is a function of the 3pt circuit, right, not the added TnT controls?

Got a replacement set of the spanners coming, but for now used a 24 inch pipe wrench to get it loose. Did not mark it up too badly. That's fine for the "Boom" cylinders, but the bucket cylinders have a smaller gland, and not as "thick" so it will be harder to get a pipe wrench on that...

Need to find a good relatively cheap tool to help remove a cylinder end cap, with "radial" holes, picture attached. I have tools to remove the ones with holes "on top". Seems like Kubota chose hole sizes a bit small for most tools for that cylinder diameter. Bought a "gear wrench" set on...

From what I read, .049 is good for 1900 psi, which is marginal for the B21 which can be just under 2100. I guess that is close enough though? But I wonder about "carbon steel" vs stainless. Are the factory lines stainless or plain? Never seem to corrode, so figured they must be stainless...

What tool did you use for flares> The Ridgid and some others claim up to 0.035 tubing.

What is the purpose of the "DPOCV lock valve"?

What steel did you use for the hard lines? What flaring tool (37 degree?)